Reader support keeps this site open, opinionated, and happily independent. As an Amazon Associate, I earn from qualifying purchases.11 Best Band Saw For Resawing | Resaw Up To 13 Inches Deep

$891.88as of Jul 9, 3:51 AM

Get It On Amazon

The WEN BA1487 delivers the deepest factory resaw capacity in its price class — 8.85 inches — from a 9.5 amp motor that rips through eight-quarter hardwood without bogging. The 13.38-inch throat width accommodates wide panels, and the dual-speed drive (1480 or 3280 FPM) lets you dial back for hardwoods or open up for softwoods and curves. The 21.5 x 15.75-inch cast aluminum table is flatter than expected at this level, and the included circle cutting guide adds unusual versatility for a resaw-focused saw.

Users consistently praise the 30-minute setup time and the heavy-duty feel — the saw weighs over 138 pounds, which dampens vibration noticeably compared to lighter 14-inch models. The stock fence, however, draws consistent criticism for being imprecise and requiring frequent re-squaring during tall resaw passes. Many owners recommend budgeting for an aftermarket fence upgrade immediately. The miter gauge T-slot also does not slide smoothly, which matters less for resaw but annoys during crosscut work.

For the buyer who needs 14-inch floor-standing capacity but cannot justify premium pricing, the WEN BA1487 offers the most resaw height per dollar available. Pair it with a quality 1/2-inch or 3/4-inch resaw blade and a better fence, and it will produce clean veneer from thick lumber that would stall smaller motors. The plastic dust drawer and work light feel budget-oriented, but the core cutting capability is genuinely impressive.

$1,399.99as of Jul 9, 3:51 AM

Get It On Amazon

The QD-KYOHO 14-inch brings a 2 HP motor and a massive 13-inch resaw capacity to the mid-range tier, specs that typically require spending significantly more. The 14-amp motor at 120V provides the torque to push a wide resaw blade through thick hardwood without slowing, and the dual-speed transmission (1445 and 2950 FPM) gives you both power and finish options. The 21.5 x 15.75-inch cast iron table with integrated bogie system offers a stable, flat platform for tall workpieces, and the overload protection adds safety during heavy cuts.

User reports highlight a solid, vibration-free cut after proper setup, with several comparing the build favorably to higher-priced Rikon and Jet models. The saw arrived well-packed and required straightforward assembly, though the included instructions left some details unclear, particularly around blade guide alignment and tracking adjustments. A few owners noted surface rust developing on the cast iron table despite factory coating, and the stock blade performance is adequate but not exceptional for resaw work.

For the woodworker who needs 13 inches of resaw capacity without jumping to the premium tier, this QD-KYOHO model is a strong contender. The 302-pound weight anchors it firmly on the floor, and the 111-inch blade length allows for a full range of blade widths. Plan to spend an hour fine-tuning the guides and replacing the blade with a dedicated resaw model, and this saw will deliver consistent veneer from timber that would challenge any 1 HP machine.

$499.99as of Jul 9, 3:51 AM

Get It On Amazon

The Hoteche 12-inch offers a 7-amp motor that provides adequate power for resawing stock up to 5 inches deep, making it suitable for smaller projects and hobbyist workshops where floor space is limited. The dual-speed control (7.6 and 15.8 m/s) allows you to slow down for dense hardwood or speed up for softwood and curves. The 19.3 x 15.3-inch table tilts to 45 degrees for bevel work, and the included stand brings the saw to a comfortable working height without taking up permanent floor space.

Users generally report satisfaction with the saw’s cutting performance on dimensional lumber and hardwood up to four inches thick. The setup process drew mixed feedback — several owners found the directions vague and needed extra time to align the blade guides and tracking correctly. A small number of critical reviews mention the blade coming off during operation when cutting bone or frozen meat (indicating the saw is sometimes used outside its intended woodworking scope), but for standard wood resaw tasks, the blade tracking holds reliably after proper adjustment.

This is a solid entry-level option for the woodworker who occasionally resaws boards up to five inches thick and wants a compact footprint. The 130-pound total weight with stand provides decent mass for a benchtop-class machine, and the 2320mm blade length supports a range of common blade sizes. It will not compete with a 2 HP 14-inch floor model for production resawing, but for small shop use and light veneer work, it delivers respectable results.

$1,549.00as of Jul 9, 3:51 AM

Get It On Amazon

The JET JWBS-14SFX represents a serious step up in engineering for resaw work, starting with its 1.75 HP motor and massive 360-square-inch cast iron work surface. The factory resaw capacity exceeds 13 inches without needing an aftermarket riser, and the heavy-duty tubular steel welded frame keeps vibration virtually nonexistent even when feeding thick hardwood at the full 116-inch blade length. The tool-less, independently adjustable ball bearing blade guides — both upper and lower — make tuning the blade support fast and precise, which directly improves cut quality on tall workpieces.

Users consistently praise the fit and finish, noting the table is dead flat, the trunnion system adjusts smoothly with single-point control, and the dual 4-inch dust ports keep the work area clear during extended resaw sessions. Assembly took most owners a couple of hours, and the main complaints center on the difficulty of moving a 272-pound machine into position and the tension gauge requiring aftermarket calibration for accuracy. The tool-less guide adjustment is a genuine time-saver when switching between resaw and curve-cutting configurations.

For the dedicated woodworker who resaws regularly and expects consistent, repeatable results, the JET JWBS-14SFX is a benchmark choice. The five-year warranty (two-year for commercial use) adds confidence, and the included resaw fence provides better stability than most stock fences in the category. Pair it with a premium carbide-tipped resaw blade, and it will produce book-matched veneer from 12-inch stock with minimal drift and a surface that requires little sanding.

$1,979.00as of Jul 9, 3:51 AM

Get It On Amazon

The Powermatic PWBS-14CS combines a legendary Baldor motor with Carter quick-tension lever technology, making blade swaps and tension relief fast enough to encourage proper storage habits — the detension setting extends blade life during non-use, which matters when you own multiple blades for different resaw tasks. The 93.5-inch blade length is slightly shorter than most 14-inch saws, but the precision-balanced nine-spoke cast iron wheels deliver remarkably smooth blade travel with minimal vibration. The micro-adjustable dual bearing guide system, above and below the table, provides close blade control with less friction than ceramic alternatives.

Users consistently highlight the quiet operation and smooth power delivery of the Baldor motor, noting that the saw handles thick oak resawing and veneer production with no strain. The included T-square style fence with a 4-inch resaw attachment offers good rigidity, though some owners upgrade to a taller fence for maximum stock support. The 60-watt adjustable lamp provides direct illumination on the cut line, and the chip blower keeps the kerf visible during deep cuts. Assembly requires two people, especially when installing the drive belt, and the included blade is universally described as junk — a replacement is mandatory before serious resaw work.

This saw is built for the woodworker who prioritizes cut quality and precision over raw speed. The Carter quick-tension and tool-less guide adjustments make blade changes painless, which encourages switching between a wide resaw blade and a narrower blade for curves. If your shop produces book-matched panels or thin veneer from expensive hardwood, the Powermatic PWBS-14CS delivers the stability and adjustability needed for consistent results.

$2,398.00as of Jul 9, 3:51 AM

Get It On Amazon

The Laguna 14BX is engineered around a 2.5 HP motor running on 220V, delivering the torque necessary to push wide resaw blades through 12-inch stock without hesitation. The 38-inch table height reduces back strain during long resaw sessions, and the 21.5 x 16-inch table provides ample support for tall workpieces. The ceramic blade guide system generates less friction than ball bearings, resulting in cooler blade operation and reduced drift — a real advantage when producing thin veneer from dense lumber.

User feedback is polarized. Many owners report outstanding results with minimal setup — cuts that produce zero drift on the first test pass, quiet operation, and effortless resawing of 10-inch walnut into 1/8-inch veneers. The saw does not come with a blade, which frustrates some buyers, and a few units arrived with minor shipping damage, a warped table insert, or a non-square fence that required correction. The lower guide adjustment knobs are described as tight, and the dust collection brush bolts can loosen during shipping. Once properly set up, however, the 14BX cuts dense oak smoothly with no vibration, and the foot brake adds a welcome safety feature.

The Laguna 14BX is a specialist tool for the resaw-focused woodworker who already has 220V power in the shop. It demands a premium investment and some initial tuning patience, but the ceramic guide system and high torque motor deliver a cut quality that justifies the cost for those producing exhibition-grade veneer or working with expensive hardwoods. The single-speed transmission (1930 FPM) is optimized for resaw and general woodworking, not metal cutting.

$417.19as of Jul 9, 3:51 AM

Get It On Amazon

The DEWALT DWM120K is a portable deep-cut band saw designed primarily for metal cutting, featuring a 10-amp motor and a 5-inch deep cut capacity for round or rectangular stock. The variable speed dial (100-350 SPM) lets you match blade speed to the material — slow for tool steel and stainless, faster for aluminum and copper. The integrated LED work light and hang hook make it practical for jobsite use, and the dual-bearing blade guide rollers increase durability in the blade support system.

Users praise the saw’s portability and cutting accuracy, noting it produces cleaner, faster cuts than abrasive chop saws with significantly less mess. The tool-less blade change system is a time-saver, and the three-position front handle provides good control for various cutting angles. The stock blade is described as poor, and owners recommend upgrading to Lenox or equivalent bi-metal blades immediately. The lack of a trigger lock is noted by several users who added a velcro strap for hands-free operation when the saw is mounted vertically in a SWAG table.

This is not a resaw machine for woodworking — it is a portable metal cutting tool. It earns a place in this guide because its deep-cut capacity and variable speed make it the right choice for fabricators who cut metal stock all day. For wood resawing, look at the floor-standing models. For clean, portable metal cutting with accurate depth control, the DWM120K is a proven workhorse.

$1,802.56as of Jul 9, 3:51 AM

Get It On Amazon

The KAKA INDUSTRIAL BS-912B is a horizontal metal-cutting band saw with a 9-inch round and 9×12-inch rectangular cutting capacity, powered by a 1.1 kW motor with four blade speed options (32-115 MPM). The precision hydraulic feed system provides controlled, consistent blade descent, reducing blade deflection and burr formation while extending blade life. The quick-release vise rotates 0-45 degrees for accurate miter cuts on tubing and structural shapes, and the integrated coolant system manages heat during extended cutting sessions.

Users report that the saw cuts straight and square right out of the crate, with the included blades performing adequately for general fabrication work. The four-speed pulley adjustment is straightforward, and the hydraulic downfeed works well once properly calibrated. Some owners noted the saw appears smaller than expected in photos and required minor fixes — a misaligned hydraulic bracket that caused stick-slip, and a missing drain strainer that required a hardware store solution. The blade guide bearings do not support the blade as fully as some prefer, but with light feed pressure the cuts remain straight.

This is a dedicated horizontal metal-cutting bandsaw for fabrication shops and heavy-duty hobbyists who need to cut steel, aluminum, and alloys accurately. It is not suitable for wood resaw work. The 573-pound weight requires a concrete floor and a loading dock or liftgate delivery, but the build quality and cutting accuracy justify the industrial price tag for shops that cut metal daily.

from $1,611.00as of Jul 9, 3:51 AM

Get It On Amazon

The KAKA INDUSTRIAL BS-1018B steps up to a 2 HP motor on 220V single phase, delivering the power needed to cut 10-inch round and 10×10-inch rectangular steel, aluminum, and alloys. Four blade speeds (35, 60, 88, 115 MPM) cover everything from thick carbon steel to thin-wall tubing, and the hydraulic feed and integrated coolant system work together to maintain blade life and cut quality over long production runs. The reinforced cast iron base provides the mass required for vibration-free operation, and the automatic shut-off stops the machine after completion for unattended operation.

Owners report straight, square cuts with minimal effort after initial setup. The included bi-metal blades are adequate for general work, and the coolant pump and chip trap function reliably. A few users noted that the saw is physically smaller than product photos suggest, and that the hydraulic downfeed bracket can cause stick-slip if not aligned correctly during assembly. The blade guide bearings push the blade slightly off track under heavy load, but light feed pressure keeps cuts straight. The 849-pound weight and liftgate delivery requirement are significant logistics considerations.

This machine is built for professional fabrication shops and serious metalworking enthusiasts who need a reliable, high-capacity horizontal bandsaw for daily production cutting. It is not a wood resaw tool. If your shop routinely cuts 10-inch round stock or structural shapes in steel and alloys, the BS-1018B offers industrial capability at a price well below most European competitors, with adequate support from an established importer.

$382.24as of Jul 9, 3:51 AM

Get It On Amazon

The WEN BA3962 is a 10-inch benchtop bandsaw with a 3.5-amp motor and a 6-inch cutting depth, designed for the hobbyist who needs occasional resaw capability without dedicating significant floor space to a larger machine. The dual-speed drive (1520 or 2620 FPM) provides basic material flexibility, and the 14.1 x 12.5-inch cast aluminum table bevels to 45 degrees for angled work. The included fence, miter gauge, and 3-in-1 dust port give it a complete out-of-box package for light workshop tasks.

Users note that the saw is quiet and reasonably powerful for its size, handling 4-inch pine and oak resawing well with the upgraded blade recommended by nearly every owner. The stock 3/8-inch blade is adequate for curves but not ideal for resaw. The fence requires frequent squaring and is not rock-solid, and the guide bearings are finicky to adjust. A few owners mention the miter slot is an odd size and the work light is dim, but for the price point, the cutting capability is generally praised. The 3.5-amp motor limits the saw to softwoods and thinner hardwoods — forcing a cut through dense material will cause it to bog down.

This is a budget-friendly entry point for the beginning woodworker who wants to try resawing without a large investment. It will produce acceptable results on softwood and thin hardwood boards up to 4-5 inches tall. For anyone serious about resawing hardwood at 6-inch depths regularly, a 14-inch floor model with higher amperage is the better long-term investment. The WEN BA3962 is best viewed as a learning tool and light-duty shop companion.

$436.00$459.00Prime priceas of Jul 9, 3:51 AM

Get It On Amazon

The QD-KYOHO 10-inch bandsaw uses a 5.3-amp motor that delivers slightly more torque than the WEN 10-inch, with a cutting height of 4.75 inches and a 9.625-inch throat width for moderate resaw tasks. The dual-speed transmission (1515 and 3280 FPM) covers both hardwood and softwood ranges, and the 20.5 x 17.5-inch table is unusually spacious for a 10-inch saw, providing good support for wider boards. The detachable dual-sided fence assembly allows use from either side of the blade, a convenience feature for different workflows.

Users report the saw cuts smoothly and accurately after a somewhat tedious setup process. The instructions are described as unclear in spots, and several owners spent significant time aligning the blade guides, tension, and tracking before achieving clean cuts. A few buyers noted that the table developed surface rust despite factory coating, and the thumbscrew for the guide stripped on one unit after a month of use. The 5.3-amp motor provides adequate power for trim carpentry and small resaw tasks, but it struggles with blades narrower than 1/4-inch — the tracking mechanism cannot handle very thin blades reliably.

This saw is best suited for the hobbyist who needs a compact 10-inch machine for light-duty resawing of softwood and thin hardwood up to 4 inches. The larger table and dual-sided fence are genuine advantages over other 10-inch models, but the setup demands and occasional quality control issues mean it requires some mechanical comfort to dial in properly. It is a capable starter saw, not a production resaw machine.