You grab a drill and try to sink a screw into brick, but the bit skids sideways, smokes, or just snaps. Brick is hard and abrasive — a standard twist bit will go dull in seconds. You need a masonry bit with a carbide tip (a hard metal point) that grinds through the material instead of bouncing off. This guide cuts through the options to show you which bits actually survive brick and concrete, and which will waste your time.
I’m Rikta — the co-founder and writer behind FitlyFast. This guide is built by comparing the manufacturers’ published specifications and the patterns across verified customer reviews, so you get each pick’s real strengths and trade-offs instead of marketing spin.
Mounting a security camera, hanging shelves, or drilling anchor holes for a heavy fixture — picking the right bit for drilling brick can turn a five-minute job into a quick success, or into a frustrating hour of stalled progress.
How To Choose The Best Bit For Drilling Brick
Brick is dense, abrasive, and unforgiving. A general-purpose twist bit will dull almost instantly, so you need three things: the right tip material, the right shank (the part that goes into the drill), and the right cutting geometry. Here is what to check before you buy.
Carbide Tip Grade
The tip is what actually cuts into the brick. Cheaper bits use a soft steel tip that loses its edge after a few holes. Look for bits with a carbide tip, preferably YG6X or YG8X tungsten carbide — these ratings (numbers that refer to the grain size and binder content of the carbide alloy) tell you the tip is hard enough to scrape through brick without wearing down fast. The Bosch set uses a diamond-ground carbide tip that buyers report cuts like “frozen butter” in a hammer drill (a drill that pounds forward as it spins).
Shank Type and Compatibility
A 1/4-inch hex shank (a six-sided shaft) is the standard for modern drill chucks (the jaws that hold the bit) and impact drivers (a tool that hammers in bursts). It locks into your tool without slipping, which matters when you are pushing hard into brick. Some bits still use a round shank, which can spin inside the chuck under heavy pressure. Every bit on this list has a hex shank, so you can swap bits quickly without re-tightening the chuck.
Cutting Angle and Flute Design
The cutting angle (the angle of the tip’s point, measured in degrees) determines how aggressively the bit bites into the material. A sharper angle around 90 to 110 degrees is ideal for brick and concrete — it bites in without skating (sliding across the surface). The flutes (the spiral grooves along the bit’s body) carry dust out of the hole so the bit does not get clogged. Deeper, wider flutes clear debris faster, keeping the bit cooler and extending its life.
Quick Comparison
On smaller screens, swipe sideways to see the full table.
| Model | Category | Best For | Key Spec | Amazon |
|---|---|---|---|---|
| Bosch LBHX0035 | Premium | Hammer drill durability | 120-degree diamond-ground tip | $17.99Amazon |
| BGTEC 10pc Set | Premium | Tile and porcelain drilling | YG6X tungsten carbide tip | $21.99Amazon |
| Pro Edge 14pc Set | Premium | Longest set with shockproof shank | 14 pieces, double U-flute | $26.99Amazon |
| DKIBBITH 10pc Set | Mid-Range | Value with Bosch-comparable performance | 118-degree spear point tip | $14.99Amazon |
| Cortool 7pc Set | Mid-Range | Concrete and stucco walls | 90-degree split point, YG8X carbide | from $11.44Amazon |
| UBESTHS 10pc Set | Budget | Best budget variety pack | 6.35mm cutting diameter, 10 pieces | $15.99Amazon |
In‑Depth Reviews
1. Bosch 5 pc. 3/16 in. X 6 in. Hex Shank Hammer Drill Masonry Bits LBHX0035
$17.99as of Jul 5, 6:22 AM120-degree cutting angle — 33% wider than standard 90-degree bits — makes the Bosch LBHX0035 the top pick for anyone drilling dozens of holes in brick with a hammer drill and wanting a bit that stays sharp. The asymmetric diamond-ground carbide tip bites aggressively into masonry, and owners mention it cuts through brick “like it’s butter.” Milled U-flutes with a deep-cut spiral clear brick dust fast enough to keep the bit cool on long runs; one reviewer drilled at least 40 holes at 3.5 inches deep each in concrete with proper cooling. The hex shank locks into both impact drivers and hammer drills, so you do not need to swap chucks.
These bits perform poorly in an impact driver because the impact mechanism does not deliver the same straight hammering action as a dedicated hammer drill — you really need the right tool to unlock their potential. For anyone drilling into brick regularly with a hammer drill, this set is the most durable investment, with the understanding that only 5 bits (all 3/16-inch) means no size variety.
For brick-drilling endurance, this Bosch set is the one to beat.
Why it’s great
- Diamond-ground carbide tip stays sharp through 40+ holes in concrete
- 120-degree cutting angle bites into brick without skating
- Deep-cut U-flutes clear dust fast, keeping the bit cool
Good to know
- Needs a hammer drill to perform at its best — impact driver results are weaker
- Only 5 bits in the set, all 3/16-inch, so no size variety
- Premium price for fewer pieces than budget sets
2. BGTEC Masonry Drill Bits, 10pcs 5MM*2+6MM*4+8MM*2+10MM+12MM Tungsten Carbide Tip Tile Drill Bit Set
$21.99as of Jul 5, 6:22 AMCompared to the top pick Bosch, the BGTEC set gives you 10 bits versus 5 — a 2x gap in quantity for roughly the same price — but each bit uses a YG6X cemented carbide tip (a grade of tungsten carbide known for high hardness and wear resistance) rather than Bosch’s proprietary carbide formulation. The precision crosshead design reduces skating on glossy surfaces, and the hex shank is quick-fit compatible (it snaps into the chuck without tightening the jaws manually). The 5mm to 12mm range covers anchors from small picture-hanging sizes up to larger fixture bolts, and customers note that drilling 24 clean holes in porcelain tile for mirrors and hooks with no chipping is the kind of real-world result that sets this kit apart.
Starting at a 45-degree angle and gradually bringing the bit to 90 degrees prevents slip and extends bit life, according to reviewers. The manufacturer does not emphasize water cooling enough in the instructions, but reviewers consistently report that dipping the bit in cold water every 20-30 seconds dramatically improves performance in hard tile. The YG6X carbide tip handles porcelain tile, brick, and concrete without chipping.
Choose the BGTEC over the top pick if you need multiple sizes for tile work and want one set that covers most household drilling jobs.
Where it shines
- 10-piece set covers 5mm to 12mm for anchors and bolts
- YG6X carbide tip drills 24+ clean holes in porcelain without chipping
- Quick-fit hex shank snaps into chucks instantly
Worth noting
- Requires water cooling every 20-30 seconds in hard tile
- Starting at a 45-degree angle takes practice
- Bits are shorter than some competitors at about 3 inches
3. Pro Edge 14 Pcs Masonry Drill Bit Set 5/32″-1/2″, Carbide Concrete Drill Bits with Shockproof Hex Shank and Industrial Carbide Bit Tip for Brick/Glass/Cement/Tile/Plastic, with Storage Box
$26.99as of Jul 5, 6:22 AMYou are tackling a big project and want every size you might need — plus backups. The Pro Edge 14-piece set gives you two of each size from 5/32-inch up to 1/2-inch, so you never stop mid-job to hunt for a fresh bit. Its 110-degree cutting angle splits the difference between the aggressive 120-degree Bosch and the conservative 90-degree Cortool, offering a good balance of bite speed and tip strength on brick and concrete. The double U-shaped groove design (two deep channels instead of the typical single spiral) clears dust faster and keeps the bit running cooler during long drilling sessions. Reviewers point out it lasts longer than Milwaukee bits they were using alongside it — with water cooling, the bits survived twice as long. The shockproof hex shank adds a small shock-absorbing groove near the shank that reduces vibration transfer to your drill, which is noticeable on harder materials like poured concrete. The included plastic storage box keeps every bit organized, so you are not digging through a drawer to find the right size.
14 pieces is more than any other kit on this list, and having duplicates of each size means you can keep one sharp and one slightly dulled for rough-in work. For anyone planning a multi-day renovation that hits brick, concrete, and tile, this set eliminates the need to buy backups separately. It is a premium price for the largest set, but water cooling is still essential for concrete work.
With water cooling, reviewers report these bits survive twice as long as Milwaukee bits — a standout spec that makes this 14-piece set the durability king of the guide.
What stands out
- 14 pieces with two of each size for uninterrupted work
- Double U-flute design clears dust and dissipates heat better
- Shockproof shank reduces vibration transfer to the drill
The trade-offs
- Premium price for the largest set
- Water cooling still essential for concrete work
- Storage box is practical but not impact-resistant
4. 10-Piece Glass Concrete Drill Bit Set, Masonry Drill Bits for Brick, Plastic and Wood, Hex Shank Tungsten Carbide Tip (DKIBBITH)
$14.99as of Jul 5, 6:22 AMThe most important number in this category is how many holes a single bit survives before going dull, and the DKIBBITH set punches above its price — one reviewer drilled 20 holes on a single bit and it was still cutting. With a 118-degree cutting angle and a spear-point tip (a pointed tip shape that reduces walking on smooth surfaces), these bits start cleanly on tile and brick without sliding around. At 0.13 inches minimum bore diameter, the smallest bit is nearly 6x smaller than the UBESTHS set’s 0.75-inch minimum, making this kit far better for fine pilot holes (starter holes for larger bits) and small anchors.
The catch is that these bits need cooling water when drilling ceramic or hard tile continuously, and some shoppers say that the first set wore quickly without proper cooling. But reviewers who used water cooling found the bits outlasted their Bosch equivalents. The set covers 3mm to 10mm diameters, which covers most household anchor sizes, and the hex shank fits all standard drills. One reviewer noted “same quality as my Bosch and DeWalt bits.”
At a price that undercuts the premium sets while delivering comparable performance per bit, the DKIBBITH is the price-to-performance sweet spot for people who need reliable brick drilling without paying for a brand name.
The upsides
- One bit drilled 20 holes and kept cutting
- 118-degree spear point reduces walking on tile and brick
- 3mm smallest bit great for fine pilot holes
Keep in mind
- Water cooling required for hard tile to avoid premature dulling
- Not for impact drivers — best used in hammer drills
- Some buyers reported oily residue on arrival
5. Masonry Drill Bits Set for Tile, Brick, Cement, Concrete, Glass, Plastic, Cinder Block, Wood, Fully Ground with Carbide Tips and Hex Shank Quick Change (Cortool 7PCS Set)
from $11.44as of Jul 5, 6:22 AMWhat you actually get at this lower price is a 7-piece set with 6-inch bits (versus the DKIBBITH’s 3 inches), using YG8X tungsten carbide (a slightly tougher grade than YG6X, with more cobalt binder for impact resistance) and a 90-degree cutting angle, which is 33% narrower than the Bosch’s 120-degree angle. That sharper point makes these bits bite into hard concrete and stucco walls effectively, but also makes them more prone to chipping if you push too hard or drill at a wonky angle. One buyer drilled through 4-inch concrete successfully and reported the bits “worked great,” while another broke the first bit and had to switch to a backup — so the technique matters here.
The 7-piece set includes 5/32-inch to 3/8-inch sizes, all 6 inches long, which gives you extra reach for drilling through thick walls. The anti-skid triangle shank design (a triangular-shaped shank that resists spinning in the chuck under load) keeps the bit stable in the drill even at high torque. Reviewers also note that the laser-etched size markings on the shank are very hard to read, but the bits themselves are durable enough to last nearly two years of constant use drilling into concrete once a day.
Choose the Cortool set over the DKIBBITH if you need longer bits for thicker walls and prefer a tougher carbide grade for impact-heavy work — it is perfect for the budget buyer who prioritizes reach and impact resistance over ease of reading size markings.
Why we’d pick it
- YG8X carbide is tougher than YG6X for impact drilling
- 6-inch length reaches through thick brick walls
- Anti-skid triangle shank resists slipping in the chuck
A few caveats
- 90-degree tip is sharper and more prone to chipping if angled wrong
- Only 7 pieces — fewer sizes than budget-friendly 10-piece sets
- Size markings etched on the shank are hard to read
6. 10Pcs Masonry Drill Bits Kit for Concrete, Stone, Carbide Drill Bit Set for Glass, Brick, Tile, Plastic, Ceramic and Wood Size 5/32 to 1/2 inch (UBESTHS)
$15.99as of Jul 5, 6:22 AMThis set is perfect for the homeowner who needs an affordable, occasional-use kit for drilling brick, concrete, or tile, and who wants a 1/2-inch bit included — a size often missing from similarly priced sets. The 10 bits range from 5/32-inch up to 1/2-inch, with the largest bit’s 6.35mm cutting diameter being 59% larger than the 4mm diameter of the smallest bits in the DKIBBITH set, meaning this kit skews toward bigger holes for larger anchors and bolts.
What you give up is consistency: one buyer mentioned that the bits arrived crooked and dull with an oily residue, while other buyers described the quality as “excellent” and “good.” The step-point tip design helps reduce walking on smooth surfaces, and the wide flute design aids fast dust removal, while the hex shank fits most drills securely. This is for someone who understands that individual bits may vary, and who just needs to get a few holes drilled on a tight budget.
The uneven quality control means you might get a perfect set or a dud, so if you demand consistent quality across every bit, this is not the set for you.
Strong points
- 10-piece set includes a 1/2-inch bit, rare at this price
- Step-point tip reduces walking on smooth surfaces
- Wide flute design clears dust effectively
Before you buy
- Quality control issues — some bits arrive crooked or dull
- Only a 3-flute design, less efficient than the Bosch U-flute
- Best suited for light, occasional DIY use
Understanding the Specs
Carbide Tip Grade (YG6X vs YG8X)
This is the material at the tip of the bit that does the actual cutting. YG6X is a standard carbide grade offering a good balance of hardness and wear resistance — ideal for brick and concrete. YG8X has slightly more cobalt binder, making it tougher and more impact-resistant, which matters if you are drilling into very hard concrete or using a hammer drill aggressively. Both are far superior to steel-tipped bits that dull after a few holes.
Cutting Angle and Point Style
The cutting angle (in degrees) determines how aggressively the tip bites into the material. Sharper angles around 90 degrees bite fast but can chip, while wider angles around 120 degrees are more durable but require more pressure. Point style — spear point, split point, step point, or diamond point — affects how the bit starts: spear points are best for reducing walking on tile, split points cut aggressively, and diamond points are designed for maximum durability in hammer drills.
FAQ
Can I use a regular wood drill bit for brick?
Do I need a hammer drill to drill into brick?
Why do my masonry bits keep dulling after a few holes?
What size masonry bit should I use for a standard wall anchor?
How do I prevent the bit from walking or skating on smooth brick?
Final Thoughts: The Verdict
If you want one dependable pick, the bit for drilling brick winner is the Bosch LBHX0035 because its diamond-ground carbide tip and 120-degree cutting angle deliver unmatched durability in a hammer drill — buyers report it cuts through brick “like butter” and lasts dozens of holes without dulling. If you need a diverse set of sizes for tile work and household projects, grab the BGTEC 10-piece set. And for a big renovation covering brick, concrete, and tile, the standout is the Pro Edge 14-piece set for sheer variety and backup bits.
Product prices and availability are accurate as of the date/time indicated and are subject to change. Any price and availability information displayed on Amazon at the time of purchase will apply to the purchase of this product. As an Amazon Associate I earn from qualifying purchases.
CERTAIN CONTENT THAT APPEARS ON THIS SITE COMES FROM AMAZON. THIS CONTENT IS PROVIDED "AS IS" AND IS SUBJECT TO CHANGE OR REMOVAL AT ANY TIME.
Amazon and the Amazon logo are trademarks of Amazon.com, Inc. or its affiliates.