Our readers keep the lights on and the weekend projects moving. As an Amazon Associate, I earn from qualifying purchases.
Mounting a TV above a fireplace solves the floor-space dilemma but introduces a predictable ergonomic problem: neck strain from a screen fixed too high. A standard fixed mount locks your TV in that elevated position, forcing your chin up during every movie or game. The solution lies in choosing a bracket that drops the screen to a natural sightline when you are seated, then tucks it back flush against the wall when not in use.
I’m Rikta — the founder and writer behind FitlyFast. I have spent years analyzing wall-mount hardware, comparing articulation ranges, weight tolerances, and VESA compatibility to find the mounts that actually solve the viewing-angle problem rather than just holding a TV in place.
The right hardware changes how you use the room. This guide breaks down the best options for an above fireplace tv mount that balances extension, tilt, and ease of adjustment so your screen sits where it belongs.
How To Choose The Best Above Fireplace TV Mount
An above fireplace TV mount lives in a specific environment: high off the ground, often above a mantle, and exposed to heat from the fire below. The mount must drop the screen to a comfortable viewing height, handle the weight of a modern flat panel, and fit the stud layout behind your brick, stone, or drywall surround. Three factors separate a good mount from a regret.
Articulation and Drop Range
The whole point of mounting above a fireplace is to reclaim floor space, but a TV fixed six feet off the floor forces an unnatural upward gaze. Look for a mount that offers at least 12 inches of vertical drop — either through a manual pull-down mechanism, a motorized arm, or a long articulating arm that tilts and swivels the screen downward. A fixed low-profile bracket saves depth but does nothing to fix the viewing angle, so it only works if your seating is far enough back that looking up is comfortable.
VESA Pattern and Weight Capacity
Every TV has a VESA pattern — the horizontal and vertical distance between the mounting holes on the back of the panel. Common patterns for the 40-to-70-inch range include 200x200mm, 400x400mm, and 600x400mm. The mount you choose must support that exact pattern and exceed the TV’s weight by at least 20 percent. Above fireplace mounts often hold heavier TVs because larger screens are common in living rooms, so confirm the rated load includes your speaker bar and any accessories you plan to hang.
Installation Constraints: Studs, Heat, and Clearance
A fireplace surround is rarely a simple sheetrock wall. Masonry or tile requires specific anchors or concrete screws, while wood studs behind drywall demand precise alignment. Measure your stud spacing — 16-inch centers are standard, but 24-inch layouts exist in some homes. Also account for mantle depth: if your mantle protrudes more than 8 inches, an articulating arm that extends forward and then drops is necessary to clear the ledge. Do not install any mount directly into drywall alone; every pound of TV weight must transfer to the stud or masonry behind the surface.
Quick Comparison
On smaller screens, swipe sideways to see the full table.
| Model | Category | Best For | Key Spec | Amazon |
|---|---|---|---|---|
| VIVO Motorized Pull Down | Motorized | Effortless height adjustment | 23 in. vertical drop range | Amazon |
| FORGING MOUNT Heavy Duty | Premium Full Motion | Large screens over 75 in. | 198 lbs weight capacity | Amazon |
| Perlegear PGXLF02 | Premium Full Motion | Wide 42-97 in. TV range | 40.1 in. full arm extension | Amazon |
| VIVO Counterbalance VW03G | Mid-Range Articulating | Manual height adjust above fire | 12.5 in. height adjustment | Amazon |
| monTEK Ultra Slim | Mid-Range Full Motion | Low profile with articulation | 1.1 in. from wall retracted | Amazon |
| Perlegear Long Arm Corner | Mid-Range Extended | Corner and deep mantle setups | 37.4 in. total arm reach | Amazon |
| Supcline Ultra Slim | Budget Fixed | Flush mount flat back TVs | 0.3 in. micro gap from wall | Amazon |
In‑Depth Reviews
1. VIVO Motorized TV Wall Mount (MOUNT-E-M070R-W)
The VIVO Motorized Mount targets the exact problem of an above fireplace installation: the TV is too high, and reaching up to adjust it is a hassle. This white bracket uses an electric motor to drop the screen up to 23 inches from its resting position, giving you a natural seated viewing angle at the push of a button. The remote works up to 100 feet away, and the motor is smooth and quiet enough not to distract during a scene change.
Weight capacity sits at 77 pounds, which covers most 37-to-70-inch flat panels comfortably. VESA patterns from 200x100mm up to 600x400mm are supported, and the mount extends between 7 and 20.3 inches from the wall surface. The unit also provides a manual +/-20 degree swivel for side-to-side adjustment, and the screen auto-straightens when raised. Installation requires double-stud or concrete anchoring, and the included drilling template keeps the process clean.
The motorized mechanism adds some depth when the TV is fully raised, so it does not sit as flush as a low-profile mount. Some users also note that the TV in the raised position protrudes farther from the wall than expected. For daily use above a fireplace, however, the convenience of a remote-controlled drop makes this the most ergonomic option on the market.
Why it’s great
- Remote-controlled motor eliminates manual lifting for daily viewing adjustments.
- 23-inch vertical drop brings high-mounted TVs to a comfortable seated sightline.
- Programmable memory positions allow custom stop points for different seating arrangements.
Good to know
- TV sits farther from the wall when retracted compared to a fixed low-profile mount.
- Weight capacity of 77 pounds limits use with very large or heavy OLED panels over 70 inches.
- Motorized components add complexity and a potential failure point over a purely mechanical bracket.
2. FORGING MOUNT Heavy Duty Long Arm TV Wall Mount
When the TV is an 85-inch behemoth or a 77-inch OLED that weighs 60-plus pounds, the FORGING MOUNT Heavy Duty is the bracket to trust. Its dual articulating arms are built from six sections of steel, rated to hold 198 pounds, and extend 42.9 inches from the wall. That extension is critical for a deep fireplace mantle — the arm reaches out and clears the ledge before swiveling the screen into the ideal position.
Compatibility covers 50 to 90-inch screens with VESA patterns up to 600x400mm. The mount swivels +/-90 degrees, tilts +5 to -12 degrees, and levels +/-3 degrees after installation. The wall plate fits 16, 18, and 24-inch stud spacing, which is rare and useful for older homes. Installation is a two-person job because the mount itself weighs 23 pounds, but the included template, bubble level, and labeled hardware bags reduce the guesswork.
The trade-off is bulk. This mount does not sit flat against the wall when retracted — it protrudes several inches due to the thick steel arms. It is also overkill for a 55-inch LED that weighs 35 pounds. For a large screen above a fireplace where clearance and stability matter, the raw strength of this bracket is unmatched.
Why it’s great
- 198-pound weight rating handles the heaviest large-format TVs on the market.
- 43-inch extension clears deep mantles and allows viewing from adjacent rooms.
- Compatible with 24-inch stud spacing, a common layout in larger living rooms.
Good to know
- Mount weighs 23 pounds and requires two people for safe installation.
- Does not retract flush against the wall when not extended.
- Over-specified for smaller TVs under 60 inches, adding unnecessary cost and weight.
3. Perlegear Long Arm Full Motion TV Wall Mount (PGXLF02)
The Perlegear PGXLF02 hits the sweet spot for large TVs that need full range of motion without the extreme weight capacity of the FORGING MOUNT. Rated for 150 pounds and screens from 42 to 97 inches, this mount supports VESA patterns up to 800x400mm — wide enough for most ultra-large panels. The 40.1-inch arm extension provides the reach needed to pull a TV forward and down from a high fireplace mount, and the pre-assembled design cuts installation time significantly.
Swivel range is +/-90 degrees, tilt spans +5 to -15 degrees, and leveling allows +/-4 degrees of post-installation fine-tuning. The wall plate accommodates 8, 12, 16, and 24-inch stud spacing, giving flexibility for non-standard framing. Cold-rolled steel construction has passed a 4x load test and 6,000-cycle durability test, so the movement stays smooth over years of daily adjustment.
The mount retracts to 3.7 inches from the wall, which is not ultra-slim but is reasonable for a full-motion bracket. Some users with thin concrete walls found they needed Tapcon screws instead of the included hardware. The long arm also means the TV can sway slightly if not fully tightened. For a living room with a 65-to-75-inch TV above a fireplace, this Perlegear offers the best balance of reach, strength, and ease of installation.
Why it’s great
- Pre-assembled design reduces installation steps compared to multi-piece brackets.
- 40-inch extension clears deep mantles and provides wide swivel for multi-zone viewing.
- Rated for 150 pounds and tested to 4x load for long-term reliability.
Good to know
- Retracted depth of 3.7 inches is not as flush as low-profile alternatives.
- Large wall plate may conflict with electrical outlets centered behind the TV.
- Heavier TVs may require a second person for safe hanging on the bracket.
4. VIVO Counterbalance TV Wall Mount (MOUNT-VW03G)
The VIVO Counterbalance mount uses a pneumatic spring to counteract the TV’s weight, letting you manually lift and lower the screen without fighting gravity. The height adjustment range is 12.5 inches, and the arm articulates with +10 to -15 degrees of tilt and a full +/-90 degree swivel. This makes it an effective manual alternative to motorized mounts for above-fireplace use — you get the ergonomic drop without relying on electronics.
The mount fits 40 to 70-inch screens weighing between 17 and 66 pounds. VESA compatibility covers common patterns from 75x75mm up to 400x400mm. The counterbalance spring requires tuning with an included screwdriver, and the TV must weigh at least 17 pounds for the mechanism to work correctly. Installation uses a single-stud wall plate, which simplifies locating a stud above the fireplace.
Some users report the TV drifts out of level over time and that the mount can squeak after months of use, though lubricant solves the noise. The TV also sits slightly off-center when fully flushed against the wall. For the price, this is the most cost-effective way to get a height-adjustable mount for a 50-to-65-inch TV above a fireplace, provided you do not mind a manual tug to lower the screen.
Why it’s great
- Pneumatic spring provides tool-free height adjustment without a motor or remote.
- Single-stud installation simplifies mounting in tight spaces above the hearth.
- Full 90-degree swivel and tilt offer versatile viewing angles from a high mount.
Good to know
- TV must weigh at least 17 pounds for the counterbalance spring to function.
- Level can drift over time and may require periodic re-tightening of tension screws.
- Squeaking noises may develop after extended use and need lubricant to resolve.
5. monTEK Ultra Slim Full Motion TV Wall Mount
The monTEK Ultra Slim mount is designed for those who want the articulation of a full-motion bracket but dislike the bulky look of extended arms. It retracts to just 1.1 inches from the wall, giving a nearly flush appearance when the TV is not in use. When you need to adjust the viewing angle, the arms extend 16.5 inches and swivel +/-60 degrees, allowing you to angle the screen downward from a high fireplace position.
This mount supports TVs from 43 to 90 inches with a weight capacity of 132 pounds and VESA patterns up to 600x400mm. Tilt is tool-free at +3 to -12 degrees, and +/-3 degrees of leveling adjustment is available after the TV is hung. The bracket includes a velcro cable management strap to keep wires organized behind the flush screen. Installation fits 16 and 18-inch stud spacing as well as concrete and brick walls.
The tilt range is relatively narrow compared to dedicated pull-down mounts, so the screen can only angle down 12 degrees. That may not be enough for a TV mounted very high above a tall fireplace. Swivel range is also limited to 60 degrees on each side rather than the 90 degrees found on longer-arm brackets. For a moderate fireplace height where the TV sits 8 to 12 inches above the mantle, this mount provides a clean look with decent adjustability.
Why it’s great
- Retracts to 1.1 inches for a near-flush appearance when the TV is not extended.
- Supports TVs up to 90 inches and 132 pounds, covering most large living room panels.
- Tool-free tilt and included cable management keep the setup clean and user-friendly.
Good to know
- Only 16.5 inches of extension may not clear a deep fireplace mantle.
- Tilt range is limited to 12 degrees, which may not be enough for very high mounts.
- Swivel stops at 60 degrees per side, less than some competing full-motion models.
6. Perlegear Long Arm Corner TV Wall Mount
The Perlegear Long Arm mount is built for tricky layouts — corner installations, rooms with roof eaves, or fireplaces where the TV needs to swing out from a side wall. The single articulating arm extends 37.4 inches from the wall and retracts to 2.6 inches, giving it the reach to position a TV in front of a fireplace even when the mount is anchored on an adjacent wall. Swivel range is +/-90 degrees, tilt is +5 to -15 degrees tool-free, and +/-3 degrees of leveling is available post-install.
Compatible with 32 to 65-inch TVs weighing up to 110 pounds, this mount supports VESA patterns from 100x100mm to 400x400mm. The single-stud wall plate keeps installation simple and allows placement almost anywhere on the wall, but the mount cannot be installed on drywall alone — a wood stud or solid concrete anchor is required. The included hardware, drilling template, and instructions make the process straightforward.
The long arm can introduce slight wobble when fully extended with a heavy TV, and the single-stud design concentrates all weight on one point. For TVs over 65 inches or heavier than 100 pounds, consider a dual-stud mount. This Perlegear is best suited for medium-sized TVs in non-standard room layouts where the arm’s reach solves a placement problem that standard brackets cannot address.
Why it’s great
- 37.4-inch extension pulls the TV far from the wall, ideal for corner or side-wall fireplace mounts.
- Retracts to 2.6 inches for a clean profile when the screen is pushed back.
- Single-stud design allows flexible placement on walls with limited stud access.
Good to know
- Single-stud mount concentrates weight, not ideal for TVs over 65 inches.
- Fully extended arm may introduce slight wobble with heavier panels.
- Not suitable for installation on drywall alone; a stud or masonry anchor is mandatory.
7. Supcline Ultra Slim Low Profile TV Wall Mount
The Supcline Ultra Slim is a fixed low-profile mount that holds the TV just 0.3 inches from the wall, creating a flush picture-frame aesthetic. It works only with flat-back TVs — not curved panels or models with protruding rear bumps — and supports screens from 14 to 80 inches up to 100 pounds. The VESA range covers 75x75mm up to 200x100mm for single-panel patterns and up to unlimited VESA for dual-panel patterns, though 100x100mm is not supported.
Installation takes under 30 minutes with the included bubble level and instructions. The mount uses solid steel construction with N52 magnets on the back to hold the TV securely. To remove the TV, you pull it forward slowly, and it detaches from the wall plate for cable access. This mount works on wood studs, concrete, and brick walls.
A fixed mount has no articulation, so it does nothing to fix the high viewing angle of a TV above a fireplace. The TV stays exactly where you put it. This bracket is only suitable if your fireplace is low, your seating is far enough back to look up naturally, or you plan to use a separate articulating arm. For those who want a clean flush look and are willing to accept the fixed position, the Supcline delivers at a budget-friendly cost.
Why it’s great
- 0.3-inch gap creates the most flush wall-mounted appearance available.
- N52 super magnets on the back keep the TV locked in place without visible fasteners.
- Wide VESA compatibility covers most flat-back TVs from small monitors to 80-inch panels.
Good to know
- No tilt, swivel, or height adjustment — the TV stays in a fixed elevated position.
- Only compatible with flat-back TVs; curved or uneven rear panels will not fit.
- Not suitable for fireplaces where the TV needs to drop to a comfortable viewing height.
FAQ
Can I install an above fireplace TV mount on brick or stone?
How far above the fireplace should the TV sit with a drop mount?
Will the heat from the fireplace damage the TV or the mount?
Final Thoughts: The Verdict
For most users, the above fireplace tv mount winner is the VIVO Motorized Pull Down because it solves the height problem with a quiet motor and 23 inches of drop, removing the ergonomic penalty of a high mount entirely. If you want a heavy-duty articulating arm for a massive 85-inch TV, grab the FORGING MOUNT Heavy Duty. And for a budget-friendly manual solution that still adjusts height, the VIVO Counterbalance VW03G offers pneumatic spring adjustment at a fraction of the motorized cost.